Our steel shot conforms to both the European CIP regulations as well as the US SAAMI Regulation. We can provide certificates of conformity upon customer request.

With recent developments in steel loads our retail company Clay & Game Reloaders can provide customers with steel shot loads in 12ga down to 410.

• Steel Shot Cartridges

  1.1 Steel shot must meet the following hardness values (Vickers):

  • Surface VH1 < 110
  • Core VH1 < 100 

  1.2 The steel shot load must be provided with a sufficiently strong and direct acting protective device designed to prevent any abrasion by the shot on the internal barrel wall (i.e. plastic or other wad). This protection must be effective for firing at temperatures from - 20ºC to + 50ºC. 

   

  1.3 The marking 'Steel Shot' must be printed on the cartridge tube.
• Standard 12 Bore Steel Shot Cartridges
  Extracted from official BASC website: www.basc.org.uk

   

  These cartridges, if they are to be fired from standard proof shotguns (i.e. those proved to 960 bar (transducer) or, previously, 850 bar (crusher)), or magnum proof shotguns (i.e. those proved to 1370 bar (transducer) or, previously, 1200 bar (crusher)) must not exceed the maximum admissible service pressure of 74 MPa (new units megapascals, in place of the old 740 bar) specified by the CIP and measured by means of a piezo-electric transducer.

   

  2.1 The steel shot diameter must be  3.25 mm (i.e. equal to or less than 3.25 mm, which is smaller than English no. 3). 

   

  2.2 The mean velocity, measured at a point 2.50 m from the muzzle, must be 400 m/s (around 1,300 ft/s).This velocity is to be measured using a cylindrical barrel and the mean value of a series of 10 shots.

   

  2.3 The momentum must be: Mo = mV ? 12 Ns. (Momentum = mass of shot x its velocity, measured in Newton-seconds (!). It is calculated by multiplying the weight of shot load (in kgs) by the velocity (at 2.5 m) in m/s. So, a 30 g load at 385 m/s has a momentum of 0.030 x 385 = 11.55 Ns i.e. just under the 12.0 Ns limit). See Endnote.

   

  2.4 Markings to be borne on the basic packaging, in addition to the normal safety warnings:

  •  'Beware of ricochets: avoid firing at rigid and hard surfaces'
  • 'Steel Shot cartridges'
• High Performance 12 Bore Steel Shot Cartridges
  Extracted from official BASC website: www.basc.org.uk

   

  These cartridges, whether 12/70 or 12/73 and longer (i.e. 12 bore cartridges for 70 mm (2 3/4in) or 73 mm chambers), can only be fired from 12 bore guns specially designed to fire steel shot ammunition and bearing the Steel Shot proof mark (this includes the words: Steel Shot and a Fleur de Lys ).

  They must all observe the maximum admissible service pressure of 105 MPa (1,050 bar (transducer)). 

   

  3.1 The mean velocity measured at a point 2.50 m from the muzzle, for any 12/70 or longer cartridge, must be 430 m/s (around 1,400 ft/s). This velocity is to be measured using a cylindrical barrel and the mean value of a series of 10 shots.

   

  3.2 For 12/70 cartridges the momentum must be: Mo = mV  13.5 Ns (see para 2.3 above). For 12/73 or longer cartridges, the momentum must be: Mo = mV  15 Ns (see para 2.3 above). See Endnote.

   

  3.3 Where the steel shot diameter exceeds 4 mm (BB or larger), only weapons having barrels with a choke less than 0.5 mm (equivalent to half choke) are to be used.

   

  3.4 Markings to be borne on the cartridge: - identification as laid down for High Performance ammunition; - the wording 'Steel Shot'.

   

  3.5 Markings to be borne on the basic packaging, in addition to normal safety warnings: - 'Only for use in weapons designed to fire steel shot cartridges and bearing the Steel Shot proof mark' - 'Where the steel shot diameter exceeds 4 mm, it is only to be fired from weapons bearing the Steel Shot proof mark and having barrels fitted with a choke less than 0.5 mm' 

  • 'Beware of ricochets: avoid firing at rigid and hard surfaces'.
• Standard 20 Bore Steel Shot Cartridges.
  Extracted from official BASC website: www.basc.org.uk

   

  In order to be fired in weapons already on the market (guns proved to 1,080 bar) these cartridges must not exceed the maximum admissible service pressure specified by the CIP of 83 MPa (830 bar) when measured by means of piezo-electric transducers.

   

  4.1 The steel shot pellet diameter must be 2.60 mm (English no. 6). 

   

  4.2 The mean velocity at 2.50 m from the muzzle must be 390 m/s (1,280 ft/s).This is to be measured using cylindrical barrel and is to be the mean value of a series of 10 shots. 

   

  4.3 The momentum Mo = mV 9.3 Ns (see para 2.3).?

   

  4.4 Markings on the basic packaging in addition to normal safety warnings: 

  • 'Beware of ricochets: avoid firing at rigid and hard surfaces' ?
  • 'Steel Shot cartridges', plus possibly the same information in one of the languages used by CIP member states. 
• High Performance 20 Bore Steel Shot Cartridges

  Extracted from official BASC website: www.basc.org.uk

  These cartridges are only to be fired from 20 bore guns specially designed to fire steel shot ammunition and bearing the Steel Shot proof mark (see para 3). They must comply with the CIP maximum admissible service pressure limit of 105 MPa (1,050 bar).

  5.1 The mean velocity at 2.50 m from the muzzle must be ? 410 m/s (1,350 ft/s). This is to be measured using a cylindrical barrel and is to be the mean value of a 10 shot series.

  5.2 The momentum Mo must be: mV ? 11.5 Ns (see para 2.3).

  5.3 Where the steel shot pellet diameter exceeds 3.5 mm (English no. 1 and larger) they are only for use with weapons having a choke less than 0.5 mm (half choke).

  5.4 Markings to be borne on the cartridge: - identification as laid down for High Performance steel shot ammunition - the words Steel Shot, plus possibly the same information in one of the languages used by CIP member states.

  5.5 Markings on the basic packaging, in addition to normal safety warnings: 

  • Only for use in weapons designed to fire steel shot cartridges and bearing the Steel Shot proof mark.
  • 'Where the steel shot pellets exceed 3.5 mm in diameter, only for use with weapons bearing the Steel Shot proof mark and having a choke less than 0.5 mm'
  • 'Beware of ricochets: avoid firing at rigid and hard surfaces'. 
• High Performance Steel Shot Cartridges.
  Extracted from official BASC website: www.basc.org.uk

   

  Shotguns specially designed to fire High Performance steel shot cartridges. These guns can use both Standard and High Performance steel shot cartridges, as defined in paragraphs 2 and 3, as well as all cartridges loaded with lead shot.

   

  6.1 The quality of the barrel material is defined as: R = tensile strength (resistance) in N/mm2 (measured on the finished gun). S = cross section in mm2 of the barrel crown, measured at the muzzle, and, in the case where the barrel has a choke, measured at a point halfway along the length of the choke. Q = R x S and must be > 65,000 N.

   

  6.2 The choke profile is to be the most elongated possible, the maximum slope recommended by the CIP being 0º 30? (angle of 1º at the centre). 
• Smooth Bore Guns for 12 Bore Steel Shot Cartridges

  Extracted from official BASC website: www.basc.org.uk

  Proof of smooth bore guns designed to fire 12 bore steel shot cartridges. This proof is carried out as follows:

  7.1 Three steel shot proof cartridges, loaded with shot of diameter 4.6 mm (between BB and AAA!), and with hardness values of VH1 between 80 and 110 (see para 1.1), are fired per barrel. Each proof cartridge must develop simultaneously: - a mean pressure of at least 137 MPa (1,370 bar) at the first measuring point; - a mean pressure of at least 50 MPa (500 bar) at the second measuring point; - for 12/70 cartridges a momentum Mo 15 Ns (see para 2.3); - for 12/73 or longer cartridges, a momentum Mo 17.5 Ns (see para 2.3).

  7.2 If the shotgun, after proof firing, complies with CIP regulations and requirements, it will be marked with the Steel Shot proof (see para 3) and in any other way laid down in the CIP regulations.

• Smooth Bore Guns for 20 Bore Steel Shot Cartridges

  Extracted from official BASC website: www.basc.org.uk

  Proof of smooth bore guns designed to fire 20 bore steel shot cartridges. This proof is to be conducted as follows: 

  8.1 Three proof cartridges, each loaded with steel shot pellets of 3.7 mm diameter (English no.1) and having a hardness value of between 80 and 110 VH1 (see para 1.1), are to be fired per barrel. Each proof cartridge must develop simultaneously:  a mean pressure of at least 137 MPa (1,370 bar) at the first measuring point ? a mean pressure of at least 50 MPa (500 bar) at the second measuring point ? a momentum Mo 14.5 Ns (see para 2.3). 

  8.2 If the weapon, after being fired, complies with CIP specifications then it is to be marked with the Steel Shot proof mark (see para 3) and any other markings as laid down in CIP regulations.

• Other Types of Shotgun

  Extracted from official BASC website: www.basc.org.uk

  Other types of shotgun. These regulations apply only to 12 and 20 bore shotguns. In time regulations for 10 bore and larger bored guns may also be developed.